Repair it yourself
Pros and cons
- + Usually the cheapest option
- + Device stays with you, no data loss from shipping
- − Risk of further damage
- − Tools needed, water resistance may be lost
No reliable spare-part prices known.
Analogue stick moves by itself
Repair probably worth itData quality: low
ClockworkPi Clockwork GameShell, Fix stick drift: we don't have our own prices for this exact model yet – for similar devices (Nintendo Switch (OLED-Modell), Valve Steam Deck) a repair shop charges about €49–€119.
Data as of:
| Verdict | Repair probably worth it (Data quality: low)estimate |
|---|---|
| Independent repair shop | open |
| Repair it yourself (parts) | open |
| Data as of | 12/11/2026 |
All prices on this page come from Germany (euros) – we don't have prices for your country yet. Enter quotes from your country in the calculator below.
We don't have verified prices for the ClockworkPi Clockwork GameShell yet. Get a quote (or check the used price on eBay) and enter the values in the calculator below – the recommendation will then use your numbers.
Possible saving
Not yet known
Get a quote and enter it in the calculator below – then we work out the exact saving.
Rule of thumb without model-specific prices for this device – a real quote makes the assessment reliable.
No reliable spare-part prices known.
Repair-shop price for similar models (Nintendo Switch (OLED-Modell), Valve Steam Deck) – get a quote for this device.
Same model, used
ClockworkPi Clockwork GameShell is no longer sold new – so we compare with the used price.
Adjust age, condition and prices – for example with a real quote from a repair shop.
Possible saving
Not yet known
Get a quote and enter it in the calculator below – then we work out the exact saving.
Rule of thumb without model-specific prices for this device – a real quote makes the assessment reliable.
Missing information:
| Option | Cost | Use | Per year |
|---|---|---|---|
| Repair it yourself | – | – | – |
| Have it repaired | – | – | – |
| Buy used | – | – | – |
| Buy new | – | – | – |
We only show parts for exactly this model. Real retailer prices appear once a retailer interface is connected; until then the links lead to the retailer's search.
Original or third-party – check with the seller
Tools: Y00 tri-wing screwdriver, Phillips PH000, Tweezers, Spudger
General procedure, not yet reviewed by an expert for the ClockworkPi Clockwork GameShell. Screw positions and cable order are in the model-specific guide (links below).
Analogue stick drift is caused by wear in the stick module. Before replacing it, try calibrating in the system settings.
Run the stick calibration in the system settings. If that helps permanently, no replacement is needed.
Loosen the screws with the right tool (Y00 tri-wing for Joy-Cons). Open the housing carefully.
There's a small lithium battery in the controller – don't bend or pierce it.
Lift the battery carefully and remove the cover plate to reach the stick module.
Open the ribbon cable latch, unscrew the old module, insert the new one and slide the cable back in.
Close the housing, calibrate and test the stick.
Repair probably worth it. Rule of thumb: this fault affects a wear part or can be fixed by cleaning – the repair usually costs only a fraction of a replacement. For comparison: for similar devices (Nintendo Switch (OLED-Modell), Valve Steam Deck) a repair shop charges about €49–€119 – sourced prices of other models, not this device. Rule of thumb without model-specific prices for this device – a real quote makes the assessment reliable.
Yes. Difficulty: medium, time needed about 30 minutes to 1 hours. You need: Y00 tri-wing screwdriver, Phillips PH000, Tweezers, Spudger. There's a small lithium battery in the controller – detach it carefully, don't bend it.
At independent repair shops near you or at the manufacturer. Our repair-shop finder searches by postcode – sorted only by distance, without paid placements.